mosaic-guitar-finished

Mosaic Guitar

Artist MC Holt-Evans of Nashville recently made a mosaic sculpture very much in keeping with spirit of The Music City, and her mosaic guitar is worth taking a look at, especially if you are considering making a mosaic on an improvised base such as a musical instrument or a piece of furniture. The instructions below could be adapted for using other household objects as a base.

mosaic guitar back side
Mosaic guitar by MC Holt-Evans has a “blue grass” color scheme.

Mosaic Sculptures on Improvised Bases

Mosaic sculptures that use household objects as their base aren’t anything new. For example pique assiette (broken plate) mosaic furniture is fairly common, as are mosaic gazing spheres made from bowling balls. (Note that my article on gazing spheres explains why hard polystyrene makes a better base than a bowling ball.) However, a guitar can be a particularly challenging choice of mosaic base for several reasons: The shape is complex and curved, and part of it (the neck) is long and thin and has a lot of corners. The wood of the guitar’s sound box is thin, and yet it has a thick layer of lacquer that must be removed before adhesives and grout will bond to it.

Prepping the Guitar

Sanding

A medium grit sandpaper (120 grit) can be used to take off any lacquers or sealants. As always, wear an N95 rated dust mask for doing this type of work. (The N95 dust masks are cheap and readily available at a building material or hardware store.) I don’t recommend wet-sanding a guitar because you want to minimize its exposure to moisture until you get it sealed because the wood is thin and easily warped by moisture.

Modifying

Are you going to want to put the strings back on the guitar after it is mosaiced? Probably so, and that mean you need to take into account the thickness of the tile you are adding to the surface and raise the nut fret that separate the head from the neck. Use a hard wood for this such as bass (the wood used for sewing boxes and buttons) and not some soft wood like balsa.

Sealing

When you reseal the guitar with a water-based primer, you should apply two thin coats instead of one heavy one. To seal her guitar, Holt-Evans used an acrylic primer called Zinsser’s Bullseye 1-2-3 because it was recommended by an artist who works with mosaic guitars. Weldbond adhesive could also be used to seal/prime a guitar, and it might be the better choice because it is the adhesive that will be used to attach the tiles, and thus you wouldn’t have to worry about how well the adhesive and primer bonded to each other, but you would still need to give the sealing coat at least a week to dry out completely and fully harden before you tiled on it. Holt-Evans reported that she left coarse brush strokes in the sealant. This improves the bonding of adhesives and grout.

Using What You Have on Hand?

Be careful selecting a primer at random because Weldbond might not bond to some of them, definitely not oil-based materials. You want an acrylic, something like an artist’s gesso and not a latex house paint. PVA’s like Weldbond won’t bond to the vinyls and other binders in some house paint. Using what you have on hand isn’t necessarily being frugal if it doesn’t last nearly as long as it would have with the right stuff.

mosaic-guitar-start
The wood of the guitar was sanded bare and sealed with an acrylic primer in preparation for mosaic covering.

Mounting the Tile

Holt-Evans used Weldbond to attach the glass tile, penny rounds, and stained glass she used.

Partially Crushed Liquor Boxes

Use partially crushed liquor boxes to cradle the guitar or sculpture while you work on it. You can rearrange the boxes to re-position the guitar as needed so that whatever part of the curved surface you are working on is facing up.

Brush on the Adhesive and Let It Get Tacky

If you are having problems with tile sliding around, use a small paint brush to spread the Weldbond onto the surface and allow to sit for a few minutes and get tacky before you add the tile. Depending on how dry or moist your air is, this can be about 15 minutes, perhaps much faster if it is dry midwinter air and the heater is running. Remember, if you let the glue skin over too much, then it won’t bond to the glass as well.

Dental Picks and Cotton Swabs

Dental picks (or tooth picks) are invaluable for adjusting the positions of tiles without contaminating your fingertips. Cotton swabs can help clean up messes with precision and not move tile out of position. Tip: Don’t thow your wet-glue swabs into the trash. Instead, let them dry out and peel the dried glue off them next session and get another life out of them.

mosaic-guitar-progress
Mounting the tiles on the primed surfaces of the guitar.

Grouting

Grouting Studio or Bench Space

I like to grout outside on a patio or some place that can be hosed off. You can use drop cloths indoors, but you still have to be relatively neat, or you will track sand on the floor and ruin it. Grout and thinset mortar are concrete, not paint. That being said, grouting inside can be done without making a mess and is routinely done by mosaic artists. A plastic folding table or a table covered in construction plastic from the building material store is ideal for a project that might require multiple sessions to grout.

Grout Colors

Black grout makes color stand out more. All grout colors are lighter when the grout hardens, especially black grout. Black grout is usually jet black when mixed up but hardens to a charcoal gray or lighter. Pure white grout makes a mosaic look like a summer camp project.

Thinset Mortar vs Grout

I prefer thinset mortar instead of grout for projects like these. Thinset has an adhesive polymer in it that makes it strong and resistant to impact. Compared to ordinary concrete and grout, thinset is a lot less likely to crack and crumble when dropped. However, thinset contracts slightly as it cures, and so you might observe hairline cracks when used on a three dimensional object that can flex slightly, such as a wooden guitar. Like grout, thinset mortar can be dyed with concrete dyes.

Special Concerns

Grouting something like this is best done in multiple sessions. Unlike a mosaic chair or desk, a guitar has multiple places where special are has to be taken in order to not soil or clog some detail. A guitar has frets and working pegs and a saddle and a sound hole to take into account. Painter’s tape can be used to protect the bare wood inside the sound hole. Use crushed liquor boxes to cradle the guitar in different orientations while you grout it.

The color of a grout can look different if different amounts of water are used to mix up different batches or if they are misted differently. Try to mix up and handle your grout in a consistent way.

mosaic-guitar-finished
Finished mosaic guitar by artist MC Holt-Evans.

Grouting Sequence

Holt-Evans started by grouting the back of the guitar because it was the largest flat area with no obstructions and therefore the most straightforward surface to be grouted. When she grouted the back, she continued the grout over the sides so that there wouldn’t be a grout seam right at the corner because corners are vulnerable places and subject to many impacts.

The head and neck were each done in separate sessions, and for both of these elements, Holt-Evans did not take the mosaic and the grout around to the sides and backs. Only the top faces were covered, and so this meant that the grout had to be tapered off to the corner.

The front of the guitar was done in a later session because of the detail work required to get the grout tapered to the edge of the sound hole. The grout was carried down over the side to join the grout from the back on the sides.

To prevent a hairline crack where new grout meets the old, you should moisten the edge of the old grout with a little water on a cotton swab before grouting. This keeps the old grout from sucking all the water out of the new grout before it has a chance to harden.


Posted

in

,

by

Comments

12 responses to “Mosaic Guitar”

  1. Cronax Avatar
    Cronax

    Hi – can you still “play” the guitar once it’s been “mosaic’d”? And if so, is the sound affected?

    1. Joe Moorman Avatar
      Joe Moorman

      Of course not. The natural resonance of the wood is totally dampened by the shell of heavy materials coating the outside.

  2. Patti Avatar
    Patti

    What about if you did mosaics on an electric guitar? Would it be usable as an instrument?

    1. Joe Moorman Avatar
      Joe Moorman

      The weight would be an issue, and I imagine it would destroy the resonance of the structure.

  3. Lynette Avatar
    Lynette

    This is a very useful article – will recommend it to anyone doing such a project for the first time. Thank you.

  4. Betty Avatar
    Betty

    Your tips are very useful and your work beautiful. I’m a beginner guitar mosaic.

  5. rebecca Avatar

    Thanks for the information on the prep! I mosaic skis and snowboards, but had a major fail on a wood substrate in the past! Thoughts on Mac Glue instead of Weldbond?

    1. Joe Moorman Avatar
      Joe Moorman

      Weldbond will not fail to bond securely to wood if it is cleaned of sealers and coatings. Weldbond is free of solvents and is archival and used by the pros and museums for restoration work. I haven’t used Mac Glue.

  6. Peggy Owens Avatar

    If you can get your hands on the Mac, it is a miracle. I have not had as good of luck with glass on wood as I have had glass on glass. And at $30.00 a bottle, I use E6000 or even clear tacky glue, then grout around, finishing with an epoxy seal.

    1. Joe Moorman Avatar
      Joe Moorman

      I’m not a fan of adhesives with volatiles. If Weldbond isn’t tacky enough straight out of the bottle, a little time and stirring can make it very tacky. Weldbond is non-toxic and doesn’t release toxic volatiles. The main limitation is that it doesn’t adhere to most plastics or polymer sealed surfaces. A wooden guitar would require sanding to remove the polymer finish.

  7. nancy may knapp Avatar
    nancy may knapp

    Thank you for this post. Quite valuable! I am about to start the mosaic process with a violin. How do I know how far down to sand to? I am afraid that I won’t know and go too far.
    Thanks for your help.

    1. Joe Moorman Avatar
      Joe Moorman

      Nancy,
      That is a valid concern, but I think you will be able to tell when you have the polymer finish removed, and that is as far as you need to go.
      Sand a sample place and place a dot of glue and see how well it bonds by scraping it off 2 days later.
      Have fun with the project!
      Joe

Leave a Reply to Patti Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.